Buying guide

LS Swap Guide: Which LS Engine and What You Need

Reviewed by the Aero Engines Inc team · checked against 7 sources listed below

Short answer: An LS swap needs more than the engine: a matching computer and harness, an EFI fuel system that holds about 60 psi, an oil pan and mounts that clear your chassis, and the right flexplate or flywheel and transmission. GM says early LS engines used a 24X crank reluctor and Gen IV engines use 58X, and the controller must match. Iron-block truck engines such as the 5.3L LM7 cost less, while aluminum LS1, LS3 and L92 engines weigh less.

LS engines in our listings

Computed from our current listings each time this page loads. Every listing shows its own price, condition and freight.

TypeListingsLowestMedianHighestCondition
LS3 / LS376 10 $3,147.93 $6,291.30 $17,453.81 10 new
LS7 / LS427 6 $6,766.47 $14,666.40 $23,134.30 6 new
LSX 2 $3,116.13 $3,989.14 $4,862.14 2 new
L83 / L86 / L8T 1 $3,726.56 $3,726.56 $3,726.56 1 used

What is an LS swap?

An LS swap means installing a GM Gen III or Gen IV small-block V8 in a vehicle that did not come with one. GM introduced the family in 1997 with the 5.7L LS1 in the Corvette. GM's own catalog notes that GM calls these engines Gen III and Gen IV, while enthusiasts call every engine on the platform "LS." Truck versions were sold under the Vortec name and generally use iron blocks and smaller displacements than the car engines.

All LS engines share 4.400-inch bore centers, 6-bolt cross-bolted main caps and a 9.240-inch deck height, which is why heads, cranks and intakes interchange so widely. The details still matter: the reluctor wheel, the intake port shape and the control system have to match each other.

Which LS engine should I use?

The table lists common factory and crate LS engines with figures from GM and Chevrolet Performance sources. Where those sources give no rating, the cell says so rather than guessing.

EngineDisplacementBlockGM-published notes
LS15.7L (346 cu in)AluminumGen III car engine, built 1997 to 2004 in the US. GM's LS1 crate engine was rated 350 hp and used a 24X reluctor wheel.
LS26.0L (364 cu in)AluminumDebuted in 2005 with the Gen IV design changes. No rating in the GM sources used here.
LS36.2L (376 cu in)Aluminum430 hp in the 2008 Corvette and as a current Chevrolet Performance crate engine with a 58x reluctor.
LR4 (Vortec 4800)4.8L (293 cu in)IronRated 275 hp by GM Performance Parts.
LM7 (Vortec 5300)5.3L (327 cu in)IronThe most common LS truck engine. Rated 285 hp by GM Performance Parts.
LQ46.0L (364 cu in)IronUsed in 2001 to 2007 GM trucks and SUVs, up to 325 hp depending on application.
LQ96.0L (364 cu in)IronShares the cast-iron 6.0L block with the LQ4. No rating in the GM sources used here.
LY66.0L (364 cu in)IronTruck 6.0L with aluminum heads. No rating in the GM sources used here.
L926.2L (376 cu in)AluminumAluminum block and heads with variable valve timing, used mainly in the Escalade and Yukon Denali.
LS364/450 (crate)6.0L (364 cu in)Cast iron452 hp, 24x reluctor.
LS376/480 (crate)6.2L (376 cu in)Aluminum495 hp, 58x reluctor.
LS376/525 (crate)6.2L (376 cu in)Aluminum525 hp, 58x reluctor.
LS376/515 (crate)6.2L (376 cu in)Aluminum533 hp, designed for a carburetor.

Iron-block truck engines are the usual budget choice. Aluminum blocks save weight. New crate engines such as the LS3 and the LS376 family come with published ratings and a known build. Browse LS crate engines or the wider Chevrolet crate engines range.

What is the difference between 24x and 58x?

The reluctor wheel on the crankshaft is what the engine computer reads to know crank position. GM's catalog says early LS engines used 24X reluctor wheels and Gen IV versions switched to 58X. It also states that the reluctor wheel must match the crankshaft position sensor and the ignition controller. Chevrolet Performance's LS control system is built for engines with a 58x reluctor, 4x camshaft indexing and electronic throttle control, which it describes as typically 2006 and newer. Confirm the reluctor before you buy a harness or computer.

What else do I need besides the engine?

Engine computer, harness and throttle

Chevrolet Performance states that its LS3 long blocks require an engine control system and harness. Its LS control kit includes the engine control module, harness, accelerator pedal and mass airflow sensor, and is designed for electronic throttle control. If you want a carburetor, Chevrolet offers the LS376/515, which it says is designed to pair with carburetor models.

Fuel system

The LS control kit requires a fuel system that holds a constant 400 kPa (60 psi) and can deliver 40 gph for LS2, LS3 and LS376 engines. Plan an EFI-rated pump, filter and regulator that meet that specification.

Oil pan and mounts

Check oil pan clearance against your crossmember and steering linkage. GM sells a Muscle Car Oil Pan Kit, P/N 19212593, which it says fits virtually all 1955 to 1995 GM front-engine, rear-drive V8 cars. Chevrolet's LS3 long block guide also warns that retrofits may need changes to cooling, fuel, electrical and exhaust systems, and that some fabrication may be required. Budget for swap mounts that suit your chassis.

Transmission, flexplate and flywheel

LS long blocks ship without a flexplate or flywheel, and a manual transmission needs a pilot bearing in the crankshaft. Engines sold with the control kit ship with an automatic flexplate, so a manual swap needs its own clutch and flywheel. The kit's harness plugs into the 40-pulse output speed sensor on 4L60 and 4L80 transmissions. Compare options in 4L60E vs 4L80E and T56 Magnum vs TKX, or browse transmissions.

Intake, exhaust and cooling

Match the intake to the heads. LS1, LS2 and LS6 use cathedral-port heads, and GM says intakes for those engines and the LS Vortec truck engines are mostly interchangeable. LS3 heads use rectangular ports and will not match Gen III intake manifolds. LS long blocks also ship without exhaust manifolds, a water pump or a starter. Choose manifolds or headers that clear your frame and steering.

How do I break in a new LS crate engine?

Chevrolet Performance specifies Mobil 1 dexos 0W-40 for its LS3 long blocks and says the engine must be primed with oil before it is started. Its break-in calls for varied loads with no wide-open throttle for the first 30 miles or one hour, then an oil and filter change, then 500 miles of normal driving before another oil and filter change. The crate engine buying guide covers break-in and warranty paperwork in more detail.

Is an LS swap street legal?

It depends on the engine and the vehicle. Chevrolet tags many LS crate engines with a Special Parts Notice saying they are for off-highway use only. EPA's engine switching policy treats a light-duty engine switch as tampering unless the result matches a certified configuration of the same or newer model year as the chassis, or there is a reasonable basis for knowing emissions are not adversely affected. In California, every engine change must pass an initial inspection at a Smog Check Referee Center. Chevrolet's E-ROD packages are its emissions-packaged option. This is general information, not legal advice, so check your state's rules before you buy.

Common questions

What is the difference between a 24x and 58x LS engine?

It is the number of teeth on the crankshaft reluctor wheel that the engine computer reads. GM says early LS engines used 24X wheels and Gen IV engines switched to 58X, and the wheel must match the crank sensor and the ignition controller. Chevrolet Performance's current LS control kit is built for 58x engines.

Does an LS crate engine come with a computer and harness?

Usually not. Chevrolet Performance states that its LS3 long blocks require a separate engine control system and harness. Its LS control kit adds the engine computer, harness, accelerator pedal and mass airflow sensor.

What fuel pressure does an LS swap need?

Chevrolet Performance's LS control kit requires a constant 400 kPa (60 psi) fuel supply that can deliver 40 gph for LS2, LS3 and LS376 engines. Check the instructions for your specific control system, since requirements can vary.

Is the 5.3 LM7 a good LS swap engine?

It is the most common LS truck engine. GM lists the 5.3L as an iron-block engine of 327 cubic inches, and GM Performance Parts rated the LM7 at 285 hp. It is heavier than an aluminum-block LS, which is the trade-off for its lower cost.

Will an LS3 intake manifold fit LS1 heads?

No. LS1, LS2 and LS6 heads use cathedral-shaped intake ports, while LS3 heads use rectangular ports with a different bolt pattern. Chevrolet states that LS3-style heads will not match Gen III intake manifolds.

Is an LS swap legal in California?

It can be, but California requires every vehicle with an engine change to pass an initial inspection at a Smog Check Referee Center. Federal policy only allows a switch that matches a certified configuration of the same or newer model year as the chassis, or that has a reasonable basis for knowing emissions are not adversely affected.

Shop the listings

Freight, returns and the startup warranty are set out in our shipping policy, return policy and warranty terms.

Sources

The facts in this guide were checked against these pages. Makers revise specifications, so confirm critical figures with the manufacturer for your exact model.